Amp hook up to stock radio, video of the day

Yahoo Answers

Things You'll Need Stereo. It shows you how to add a subwoofer to a factory system. Any help would be appreciated as always. Usually you splice into four wires - left positive and negative, and right positive and negative. If you no longer wish to receive the call, 100 free please click the button to cancel your request.

Any help you could provide would be appreciated. What is the best way and location to splice into the car with out taking away fro. Tomas, A distribution block isn't required in a multi-amp system, it just makes wiring easier and neater. This Lightning Audio L for example.

Did I need to put fuse between the first and second battery? Tracy, A capacitor provides a jolt of power to an electrical system when the demand exceeds the normal supply. Or just from the speaker to the amp.

How to hook up subs and amp to stock stereo in car
  • When I turn the volume up it doesnt make a difference for the tweeters.
  • There is no way it can discharge and charge fast enough to keep up with a high wattage system.
  • Is there any information that you would be able to give me to help me out?
  • Dejuan, It depends on how you run the grounds from each amp.
  • As for what speakers and amp to get, why don't you or your daughter give us a toll-free call at and talk to an Advisor for help building the best system.

Thankyou very much Buck for your previous answer! And if you have the room, you can definitely run two power cables from the battery to your two amplifiers. Pat, The simplest way to add an amplifier to a factory system is to get one that has speaker-level inputs.

Do I have to tear apart my whole car and tear apart the entire wiring harness in order to get all eight speaker wires to the amp? Connect your amplifier to your speaker by running the positive and negative speaker wires to the proper terminals on your speaker. Any suggestions as to why my tweeters are producing the sound they should be? Give it a try and rock on.

Adding subwoofer to stock car radio Polk Audio

How to Wire an Amp & Subwoofers Into a Stock Stereo
It Still Works
Hook up amplifier to stock radio

Hi, ukraine girl I was wondering how difficult it is to add a sub to a factory car radio? You can contact a Crutchfield Sales Advisor for recommendations via phone or chat. Most amplifiers will have outputs for at least two speakers.

It should connect as close to the subwoofer amp as possible. Or would my sub have to share the same full sound as the speakers are receiving? Connect the ground from the amplifier to the chassis. Most amps have high level inputs but most of the time I prefer to use a line out converter.

Report Abuse

Adding subwoofer to stock car radio

Can I still add the sub to the stock radio? How would i wire the speakers to my radio separate from my sub amp? What if I bought my radio harness to fit my truck only?

  1. Your advisor will be able to share relevant pages and add items to your cart.
  2. What software did you use to create the wiring diagram?
  3. Use a connection in the vehicle's fuse box that turns on and off with the car, if your receiver has no remote connection.

The following wiring diagram shows the additional wiring you'll need to add a subwoofer to a factory system. Just cut the power wire, insert the inline fuse and reattach. Free Shipping on All Orders! You show the positive connection from the battery, and the components grounding to the chassis. Oh, even though I'm using speaker level inputs I still wired an ignition turn on switch for the powered sub.

Check out this article for help with that. Wayne, Not knowing the size of your factory alternator makes it a bit difficult to tell if you'll need a high-output alternator for your system when you add your amplifier. How do I connect my new sub to my old amp? Don't forget to test your rem wire before you assume it works. All finished with your chat session?

Then access the wiring harness behind the radio. This diagram shows the general layout of an amp's wiring system without showing crossed wires, which could be confusing. For this you need power amplifier and speakers etc. Felix, The in-line fuse on the power wire by the battery protects the wire and your car from fire in the event of a short circuit. If the sound is scratchy, check that your connections are secure.

How to hook up subs and amp to stock stereo in car

Amp hook up to stock radio

Quick Links

Then you can set the receiver outputs for a subwoofer and get the bass control you're looking for. The remote turn-on lead in the diagram shows it being split from the receiver and going to two amps. You could experiment with high-pass settings for your tweeters and low-pass for the mid-bass drivers until it sounds good to you. Tell us about your vehicle. For more specific options, just get in touch with a member of Crutchfield's Sales Advisor Team via phone or chat - just click on the Contact Us link at the very top of this page.

If you're only hooking up two speakers, even less. Hook it to a fuse connected to ignition turn on, like your accessory power fuse. Dana, It sounds to me like everything you have is hooked up just fine and safely. Do you know if the stock speaker have connection for a Sub? For inside speakers, How and where do I intercept the stock wiring to be routed to the amp?

Chris, If you had bought your gear at Crutchfield, you could call Tech Support for free help troubleshooting your system. The rest of your description indicates you're aware of what's involved and have a good plan for a successful install. From the block outputs routed the wire to each amp. Why don't you give us a call and talk with an Advisor about possible solutions. If it blows again, you'll have to continue checking your power wiring, amp connections, and speaker wiring for any abnormalities.

If you bought any of your gear from Crutchfield, you could call Tech Support for free help with your system. Most amps have that feature. Already answered Not a question Bad question Other. Both of these amps equal amp, so i have a amp breaker at the battery.

Does it need to go as far back as possible? An online search should get you in touch with a car audio dealership that can deliver to your territory. Carl, Yes, you can connect that subwoofer to two bridged channels of that amp and that speaker to the other two channels bridged together.

Video of the Day

If you are referring to a car system, then you can follow the article diagram using only those components relevant to your situation. Warnings Always Disconnect the Negative terminal from your battery before doing anything with electricity on your car. Give us a call at and an Advisor will help you get what you need. And what's the point of wiring the factory speaker wires into the wiring harness for the head unit?

Buck Pomerantz

Please keep your phone line open. Mike, dating site fail That wiring kit will be fine for those two amplifiers as long as the main power cable run is no longer than about thirteen feet. The current amplifier renegade ren has an output channel. This converter can then be connected directly to your amplifier's line level inputs. Their toll-free number is on your invoice and you get free lifetime support for your products.

Speaker via speaker wire to crossover, crossover via speaker wire to amp. As the typical subwoofer amplifier will be two or three times more powerful than the full-range amp in a system, that's where the greatest demand will occur, when the bass hits. Once I install the new rear speakers, will I have to go back in and cut the speaker connection from the receiver to the factory harness? Their toll-free number will be on your invoice.

  • Line between hanging out and dating
  • Relative dating helps to determine
  • Bangladesh hook up
  • Dating websites profile tips
  • Modern dating elite daily
  • Definition of radioactive dating
  • Submissive dating online
  • Random dating chat apk